01/29/2010
RF filters, isolators, cooling, and monitor and control (M&C) systems are all selfcontained within the package.
Rack space is conserved because the amplifiers occupy only 4 rack units (7 inches) of a standard 19 inch rack cabinet. Nominal weight is 65 pounds.
The unit features a menu driven front panel display, RS232/ 422/485 serial port and Ethernet interfaces for complete computer control. Forward power, reverse power and temperature, and default parameters are easily monitored on the four line front panel display.
Gain control is provided via the front panel or through the remote interfaces.
A high frequency resonant conversion power supply is used that accepts a wide range of prime power (90 to 264 VAC). Power factor correction circuitry is also included which minimizes line current distortion and reduces the required Volt-Amps input.
Depending upon user requirements, this high power amplifier can be configured for single thread, redundant, or phase combined configurations.
…for more Xicom Technology products
Leave a Comment » | 
New Products | Tagged: rack mount SSPA, X-band, Xicom, XTRS-100X | 
Permalink
Posted by satcomresources
01/28/2010
|
The Xicom XTD750DBS1 are compact self-contained, antenna mountable power amplifiers designed for low cost installation and long life.
|
The design eliminates the need for an amplifier shelter as well as a long waveguide run between the amplifier and the antenna feed horn. RF harmonic filters, cooling, and monitoring & control systems are all selfcontained within the HPA. These features provide high reliability, low maintenance costs, and low replacement costs.
The amplifier incorporates high efficiency multistage collector TWTs. Some of the benefits of this type of TWT are: reduced prime power consumption, lower internal operating temperatures, and reliability enhancement. These benefits are obtained for both the linear and saturated modes of operation.
One of the features of the XTD750DBS1 is incorporation of power factor correction and reduces the required voltamps. The combination of power factor correction and high efficiency TWTs reduces input VoltAmps by 45% when compared to equivalent amplifiers. A high frequency resonant conversion power supply that is used accepts a wide range of prime power (180 to 260 VAC). The automatic features of the power supply include quick recovery from prime power outages and multiple helix fault resets (three fault cycles).
A complete serial monitoring and control system is built into the unit.
The XTD-750DBS1 may be configured for single thread, redundant or phasecombined operation. It can be configured to control one or two switches.
An optional linearizer is available to allow increased transmit power while meeting spectral regrowth requirements.
A remote external controller is available to operate the HPA from user selected location. Mounting brackets can be supplied to mount the HPA to most popular antennas.
…for more DBS-Band Travelling Wave Tube Amplifiers
Leave a Comment » | New Products | Tagged: DBS-Band, travelling wave tube, TWT, Xicom, XTD-750DBS | Permalink
Posted by satcomresources
01/27/2010
These high efficiency traveling wave tube amplifiers include RF gain control, a solid state pre-amplifier, RF filters, cooling, and monitor & control (M&C) systems. An integrated X-Band linearizer is available.
The dual-drawer amplifier conserves rack space and occupies only 19.25 inches (11 rack units) of a standard 19 inch rack cabinet. A complete 1:1 or 1:2 redundant TWTA system, including a redundant controller, can be mounted in a single rack.
The unit features a menu-driven front panel display and RS-232 & RS-422/RS-485 serial port interfaces for complete remote control.
Gain control is set by the front panel manual control or by computer commands sent via the remote interface(s).
The units incorporate high efficiency, multi-stage depressed collector TWTs. Reliability is enhanced because both prime power consumption and internal operating temperatures are reduced for the linear and saturated modes of operation.
…for more X-Band TWTAs
Leave a Comment » | New Products | Tagged: 2250W X-band TWTA, high power amplifier, travelling wave tube, Xicom, XTRD-2000X | Permalink
Posted by satcomresources
01/22/2010
|
The Xicom XTRD-750K is a highly efficient rack mountable traveling wave tube amplifier (TWTA) designed for test and measurement applications. |
The unit includes RF gain control, a solid state pre-amplifier, cooling, and monitoring and control (M&C) system.
Rack space is conserved because the amplifier occupies only 4 rack units (7 inches) of a standard 19 inch rack cabinet. Nominal weight is 75 pounds.
The unit features a menu driven front panel display and RS-232/422/485 serial port interfaces for complete computer control.
RF, traveling wave tube, and default parameters are easily monitored on the 4-line front panel display.
Gain control is provided via the front panel or through the serial interface.
The XTRD-750K incorporates high efficiency, multi-stage collector TWTs. Reliability is enhanced because both prime power consumption and internal operating temperatures are reduced for both the linear and saturated modes of operation.
Power factor correction circuitry is also included which minimizes line current distortion and reduces the required Volt-Amps input.
The automatic features of the high frequency resonant conversion power supply include quick recovery from prime power outages and multiple helix fault resets (three fault cycles.)
Depending upon user requirements, the amplifier can be configured for either single thread or redundant system operation.
…for more Ku-Band TWTAs
Leave a Comment » | New Products | Tagged: Ku-band, rack mount, travelling wave tube, TWTA, Xicom, XTRD-750K | Permalink
Posted by satcomresources
01/21/2010
| The Xicom XTRD-400C is a highly efficient rack mountable traveling wave tube amplifier (TWTA) designed for fixed and mobile uplink applications.
|
|
The unit includes RF gain control, a solid state pre-amplifier, RF filters, cooling, and monitoring and control (M&C) systems.
Rack space is conserved because the amplifier occupies only 3 rack units (5¼ inches) of a standard 19-inch rack cabinet. Nominal weight is 56 pounds.
The unit features a menu driven front panel display and RS-232/422/485 serial port interfaces for complete computer control. RF, traveling wave tube, and default parameters are easily monitored on the four line front panel display.
Gain control is provided via the front panel or through the serial interface.
The XTRD-400C incorporates high efficiency, dual stage collector TWTs. Reliability is enhanced because both prime power consumption and internal operating temperatures are reduced for both the linear and saturated modes of operation.
Power factor correction circuitry is also included which minimizes line current distortion and reduces the required Volt- Amps input.
…for more Xicom Technology products
Leave a Comment » | New Products | Tagged: 400W C-Band TWTA, rackmount, travelling wave tube, TWTA, Xicom, XTRD-400C | Permalink
Posted by satcomresources
01/21/2010
|
The Xicom XTD-200K is a compact, antenna mountable, traveling wave tube amplifier designed for low cost installation and long life. |
Intended for outdoor operation, the self contained XTD-200K eliminates the need for a separate amplifier shelter. In addition, the distance between the amplifier and the antenna feed horn can be short, thus eliminating long waveguide runs and their associated RF losses.
RF filters, cooling, and monitor & control (M&C) systems are all self contained within the package.
A high frequency resonant conversion power supply is used that accepts a wide range of prime power (100 to 260 VAC).
A remote external controller is available to operate the HPA from a user selected location. Depending upon user requirements, these high power amplifiers can be configured for single thread, redundant, or phase combined configurations.
…for more Ku-Band TWTAs
Leave a Comment » | New Products | Tagged: 200W TWTA, Ku-band, travelling wave tube, Xicom, XTD-200K | Permalink
Posted by satcomresources
01/19/2010
|
|
The Xicom XTD-750K is a compact, self-contained, antenna mountable power amplifier designed for low cost installation and long life. |
The XTD-750 design eliminates the need for an amplifier shelter as well as a long waveguide run between the amplifier and antenna feed horn. RF filters, cooling, and monitoring & control (M&C) systems are all self-contained within the High Power Amplifier (HPA). These features provide high reliability, low maintenance costs, and low replacement costs.
The XTD-750 uses high efficiency, dualstage collector Traveling Wave Tubes (TWT). Some benefits of this type of tube are:
- Reduced prime power consumption
- Lower internal operating temperatures
- Reliability enhancement
These benefits are obtained for both the linear and saturated modes of operation.
The XTD-750 incorporates power factor correction circuitry, which minimizes line current distortion and reduces the required Volt-Amps. The combination of power factor correction and high efficiency TWTs reduces input Volt-Amps by 45% when compared to equivalent amplifiers. A high frequency resonant conversion power supply is used that accepts a wide range of prime power (180 to 260 VAC). the automatic features of the power supply include quick recovery from prime power outages and multiple helix arc fault resets (three fault cycles).
…for more Ku-Band Travelling Wave Tube Amplifiers
Leave a Comment » | Uncategorized | Tagged: 750W Ku-Band TWTA, travelling wave tube amplifier, Xicom, XTD-750K | Permalink
Posted by satcomresources
01/18/2010
| The Squire Tech Solutions pCom™ is a mobile infrastructure trailer designed to supply essential clean power, communications, lighting, and storage for diverse locations, needs and applications. |
|
Squire Tech Solutions’ pCom™ 300 is a mission critical power communications trailer system for government and private industry mobile infrastructure needs.
The pCom™ 300 provides an immediately deployable, self contained power generator, lighting and satellite communications infrastructure where you need it. Emergency management and field operations require an infrastructure designed to solve the problems that come with the unknown. The flexible design of the pCom 300 offers an environment to operate vital equipment and services to IT and Incident Operations Management personnel.
All electronics bays have NEMA4 extreme environment enclosure with controls for humidity, water intrusion, heat, cooling, and air-born particulate filtration. The pCom’s on-board 10,000 watt ultra quiet power generation system provides for site power, core communications equipment and powerful scene lighting system. The clean power generation, a 105 gallon internal diesel tank, and an auto-acquire satellite antenna, when combined with a standard 30’ internally cabled tower, creates the ultimate response trailer. With 40 rack units of environmentally controlled rack space, pCom operators have numerous options for their critical communications equipment. Whether you run proprietary internal networks or you simply require reliable access to high-speed internet, phones, radio, video, or broadcast, the pCom 300 fulfills your needs.
Leave a Comment » | New Products | Tagged: AvL antenna, emergency communications, pCom 300, power generator, Squire Tech, trailer mounted satellite communications, wireless access point | Permalink
Posted by satcomresources
01/11/2010
This item is now configurable for easy on-line purchase!
The DMD2050 provides highly advanced and
bandwidth-efficient forward error correction (FEC).
Advanced FEC options include Turbo Product Codes
(TPCs) and Low Density Parity Check (LDPC). Legacy
support for Viterbi, Trellis, Concatenated Viterbi
Reed-Solomon, and Sequential FEC are also included.
A complete range of modulation types is supported
including BPSK, QPSK, OQPSK, 8-PSK, 8-QAM, and
16-QAM.
Advanced FEC and modulation capabilities are integrated with the revolutionary DoubleTalk® Carrier-in-Carrier® bandwidth compression allowing for maximum state-of-the-art performance under all conditions. This combination of advanced technologies enables multi-dimensional optimization, allowing satellite communications users to:
-
Minimize required satellite bandwidth
- Maximize throughput without using additional
transponder resources
- Maximize availability (margin) without using
additional transponder resources
- Enable use of a smaller BUC/HPA and/or
antenna
- Or, a combination of the above to meet
specific mission needs
Data rates range from 2.4 kbps to 52 Mbps and symbol rates from 4.8 ksps to 30 Msps.
The modem provides a standard MIL-STD-188-114 (EIA-530 / RS-422), serial interface. It can optionally be configured with EIA-613 (HSSI), G.703 (T1/E1/T2/E2 & T3/E3), DVB ASI/SPI and 10/100/1000 BaseT Ethernet Interfaces. Drop & Insert functionality is supported on the G.703 interface.
A dual IF interface supports low IF (52-88, 104-176 MHz), and L-band (950-2000 MHz) frequency ranges.
Cost-effective, ultra-high reliable systems are enabled in conjunction with the RCS-11 1:1 redundancy switch, and/or the RCS-20 M:N redundancy switch.
…for more Satellite Modems
Leave a Comment » | Satcom Resources' Website Updates, Satcom Resources' Product Configurator | Tagged: DMD2050, Mil-STD-188-165A, Military Standard, Radyne, satellite modem | Permalink
Posted by satcomresources
